Home > Product > Instruction Introduction Instruction Outline Exhibition Manual                                                 Weight   15.3kg Size   420mm x 350mm x 350mm     (The height becomes 700mm when it is extended.)                 Put the aluminum box horizontally in convenient location. Unlock the middle and lower part of linkage of aluminum box which has three part of linkage. Hold the handle, and then lift vertically, push the lower part. The box becomes table type with four poles. Check the connection balls which support four poles whether they come out clearly. Push the dial handle in the both sides, and open the lid completely.           Draw out hand piece holder and connect each hand piece with 3 way syringe. Turn the hand piece and insert. Push the scaler in the straight line and insert certainly.           Fill water or distilled water in the bottle. In case of operation, fill saline. Put the tube in the bottle, and turn the bottle to the end of right side. If you hear the sound of air leak, turn to right side more, and insert certainly. Put the tube (for filth) in the air suction filth bottle.           Put the foot pedal in convenient location for treatment. Select switch: left side for water, right side for dry. Connect the urethane hose from compressor and unit with the coupling. Open the lever to send a compressed air. When the main switch (from unit) is turned on, the pressure is delivered to the water bottle automatically and get ready for treatment. If you want to refill water, turn off the main switch. And then pull out the bottle by turning to the left side.           Weight   20Kg Size   420mm *  350mm * 300mm Tank Volume   7L       Put horizontally in the location which is ventilating well. Connect 6mm urethane hose with unit (treatment equipment). Connect 200V 50~60 Hz, and open the valve. It works automatically (5kg/㎤~8kg/㎤) when you pull the red button. If you are stepping on the suction continually, compressor may be gone too far. Even it burst and knock-down, in case of decreasing the degree (5~10 minutes later) it works automatically. After using compressor, open the drain valve everyday to remove remaining air.       Do ball bearing oil spray before using hand piece. Insert certainly the coupling which is able to rotate 360°. For changing high speed hand piece bur, press finger and then change. Don’t be the center position for the direction control (R, F) of low speed hand piece. The speed of high, low is controlled by the strength and weakness of disk pedal. It is possible to interchange with any hand piece which is 4 hole system. Integrated scaler which is 32,000 Hz, Piezo system is very soft. It works easily even you step on the disk pedal switch lightly. Scaler’s power, fuse and water are controlled by the upper valve. Scaler hand piece and tips are able to disinfect in an autoclave.       Connect the filth bottle (2L) with the hose which is under the treatment equipment. It becomes ‘turn on’ when suction holder is opened to upper direction. When you step on the foot pedal, it works. So, anybody can use easily. If you use the air suction for a long time, it will be able to add compressor load. Operate intermittently if there’s a pool of filth in mouth. If the bottle is full of filth, it will splash. Caution! Air Suction is working when you are stepping on the foot pedal and taking down the lever. When you pull up the lever, it stops working. Don’t step it on continually over 5 sec.                                   Lamp   20,000 lux     (It’s possible to control brightness and use for 5,000 hours.) Weight   3.5kg Part   Trans + Body                       Release and set up the T-shaped stand which is able to control 3 level. Hold special Java by hand, control and fix the angle and point. Electric Power: connect with input 220V, output 12V. Halogen lamp turns on when all switches are ‘on’. For the protection of the lamp, cooling fan works automatically and make it cool off.                                                     Weight   12kg Size   650mm * 1700mm * 500mm                         Unfold the front side of the legs in convenient place for treatment. When you unfold the back side of the legs, unfold completely until you hear the sound “click”. First, unfold the backrest completely like 180°, and then, unfold the leg part. Backrest and headrest are controlled 5 level, and you can hear the sound “click, click”. For the controlling of the angle, start again from the back after reaching to the maximum front. Control the height of the chair by pushing 2 switches at the same time. Natural leather sheet is light and separated anytime for change.